Pool Water Chemistry Basics
Good pool water comes down to a handful of readings: free chlorine around 1 to 3 ppm, pH between 7.4 and 7.6, total alkalinity about 80 to 120 ppm, calcium hardness roughly 200 to 400 ppm for plaster pools, and cyanuric acid near 30 to 50 ppm. Keep those in range and the water stays clear, comfortable for swimmers, and gentle on your surfaces and equipment. The rest of this page explains what each number does and how to keep it steady.
The core readings at a glance
| Reading | General target | What it does | If it is off |
|---|---|---|---|
| Free chlorine | 1 to 3 ppm | Kills bacteria and algae | Low: cloudy or green water. High: irritation and faded fabrics |
| pH | 7.4 to 7.6 | Sets how acidic or basic the water is | Low: etching and corrosion. High: scale and weak chlorine |
| Total alkalinity | 80 to 120 ppm | Buffers pH against swings | Low: pH bounces. High: pH keeps drifting up |
| Calcium hardness | 200 to 400 ppm (plaster) | Keeps water from pulling calcium out of plaster | Low: etched plaster. High: scale and cloudiness |
| Cyanuric acid | 30 to 50 ppm | Shields chlorine from sunlight | Low: chlorine burns off fast. High: chlorine works more slowly |
| Salt (salt pools) | 2,700 to 3,400 ppm | Feeds the salt chlorine generator | Low or high: the cell may shut down or wear faster |
These are widely used general ranges. Your equipment maker, particularly for salt systems, may specify slightly different targets, and those are worth following.
Chlorine: free, combined and total
Most test kits report free chlorine, and that is the number that matters most. Free chlorine is the portion still available to sanitize. Combined chlorine, often called chloramines, is chlorine that has already reacted with sweat, oils and other contaminants. It is what produces the sharp “pool smell” people blame on too much chlorine, when the real cause is usually too little.
If combined chlorine climbs above roughly 0.5 ppm, shocking the pool to a much higher level breaks those compounds down. In a busy summer, after a storm, or after a pool party, plan on shocking more often.
pH and total alkalinity work together
pH controls how well chlorine works. At 7.5 a good share of your chlorine is in its most active form. Let pH drift toward 8, and much more of it becomes the weaker form, so the same chlorine reading does less work. Low pH, on the other hand, eats at plaster, grout, metal heat exchangers and ladder anchors.
Total alkalinity is the buffer that holds pH in place. When alkalinity is too low, pH jumps around with every rainstorm. When it is too high, pH creeps up no matter how much acid you add. That is why the usual order is to adjust alkalinity first and pH second.
Raising and lowering
- Sodium bicarbonate (baking soda) raises total alkalinity with a small effect on pH.
- Soda ash raises pH more strongly.
- Muriatic acid or dry acid lowers both pH and alkalinity.
Add products one at a time with the pump running, spread them around the deep end, and wait several hours before retesting. Never mix two chemicals together, and always add chemicals to water rather than water to chemicals.
Calcium hardness and your pool surface
Water that is low in calcium tends to pull it from wherever it can, and in a gunite pool that means the plaster. Over time this shows up as rough, etched spots. Water with too much calcium leaves white scale at the waterline and on heater parts. Fill water varies from one supply to another, so test it before assuming; if it runs soft, a plaster pool will need calcium added from time to time.
Vinyl liner pools are less sensitive to low calcium, though very aggressive water is still hard on metal components. Scale at the tile line is its own problem, covered on our pool tile cleaning page.
Cyanuric acid: stabilizer for outdoor pools
Sunlight destroys unprotected chlorine quickly. Cyanuric acid, often called stabilizer or conditioner, protects it, and most outdoor pools in the Northeast do well around 30 to 50 ppm. Salt pools often run a bit higher, so check the generator manufacturer’s recommendation.
The catch is that stabilizer does not evaporate or get used up. Using stabilized chlorine tablets all season keeps adding more, and once levels get very high, chlorine works sluggishly and algae gets a foothold. Partial water replacement is the main way to bring it down, which is a job to plan carefully given the high water table in parts of Nassau County.
Salt pools follow the same rules
A salt pool is still a chlorine pool. The generator turns dissolved salt into chlorine, so free chlorine, pH and alkalinity still need regular testing. Salt pools tend to push pH upward, which means acid is a regular part of the routine. If you are considering switching, our page on salt water pool conversion explains what changes.
How often to test
- Two or three times a week: free chlorine and pH
- Weekly: total alkalinity, and salt for salt pools
- Monthly: calcium hardness and cyanuric acid
- After heavy rain, heat waves or big gatherings: chlorine and pH again
Our weekly pool maintenance checklist shows how testing fits in with skimming, brushing and filter care.
Common questions
Why is my pool cloudy when the chlorine is fine?
Cloudiness with good chlorine often points to high pH, high calcium, or a filter that is not keeping up. Check pH and alkalinity first, then look at filter pressure and run time.
Are test strips accurate enough?
Strips are fine for quick checks. A drop based test kit gives more precise numbers, especially for chlorine and alkalinity, and is worth having for adjustments.
What causes the water to turn green overnight?
Usually chlorine dropped to zero during hot weather, or stabilizer was so high that chlorine could not keep up. See our guide on clearing a green pool for the recovery steps.
Do I need to balance the water at opening and closing?
Yes. Balanced water protects plaster and equipment through the off season, and starting the summer balanced saves chemicals. Our pool closing guide covers what to check before the cover goes on.
If you would rather not chase readings all summer, we test and balance the water on every visit as part of our weekly pool maintenance. Contact us to ask about service in your part of Nassau County.
Have a question about your pool? Call (516) 414-4750 or send us a message. We serve homeowners across Nassau County.